High-quality restoration of sofas with their own hands. Restoration of the worn sofa do it yourself how to repair the sofa spring at home

Old furniture after many years of use comes in disrepair. The sofa is similar to the old, humpback camel, on the sidewalls lasted fabric, and, sitting in the chair, the fifth point can be taken to the floor? There is a very logical question: what to do?! Throw away and buy new or renovated? In our case, immediately start repairing!

For the restoration of the old sofa, we will need:

Hand stapler with 6-8 mm brackets,
Hammer, pliers, set of keys (13, 14, rarely 17),
Screwdriver with a thin stress for pulling the old brackets,
Shilo, needle (crescent), threads, wide belts, scissors,
Materials for upholstery.

Materials

For upholstery, it is best to use high-quality material of the velor type, cargo, Shenila, Zhzhkard, etc.

Rhogozhka Shenil Velor Zhzhkcard

Spring blocks or foam rubber are used as a filler in furniture production. To replace them, you need to disconnect a sleeping place from the lounge pallet (sofa) with wrench. For convenience, you can use a table that will not only reduce the time of disassembly and assembly, but also will retain health.

Disassembly of the sofa

Upholstery fabric is removed using a special device. This is a conventional screwdriver, sharpened by a special way (for pulling the bracket), or factory brackets.

Such devices are not only effective, but also safe, as they fully protect their hands from involuntary slipping.

It is necessary not to forget that the repair of sofas at home is considered to be unsafe, so excessive foresight and caution will not interfere.

After we removed the old fabric, you can proceed to replace the spring block or those springs that broke.

It is very problematic to change the spring block at home, it needs to be ordered at the factory, and it takes time.

Replacing the springs of the sofa

The marker indicates the burst spring spring block after repair

Pliers unscrew the spiral tape, if it is a rope (twine) - then cut.

We establish new springs in place, do not forget to fix them on the bottom of the frame.

Under the springs it is necessary to seal the batting so that the springs during the seating or sleep do not create an unpleasant sound.

Spring Dressing Methods Method Skip

It is very important here to know and observe proper technique top weaving to maintain the uniformity of the protrusion springs in height. You can use the options proposed above.

When the springs are replaced, laying up the top layer of hard Vatin to avoid touching the springs with a cloth.

Sewing covers

Establish the pattern and tailoring of the cover on the sofa. In order to facilitate the task, you can use the old cut, pre-transforming all the sewing items.

Remove the old fabric from the sofa. Seams gently extend to separate parts using a special decreasing device. If there is such an opportunity, time and desire, then each item can be well rejuvenated to save the original sizes.
After ironing, the details are preferably numbered to not get confused. All we have turned out, lay out on a new cut of the fabric.
It is necessary to try to decompose them so to "fit out" in a width of 1 m 40 cm - this is a standard width. Pay attention to how fabric fibers are going. Longitudinal can be used on the seat and back, and the transverse best on the sidewalls.

The complexity may occur if the tissue has a drawing. It is necessary to accurately calculate the moments of docking, for example, strips to avoid unnecessary flow. The direction of the pile is also taken into account, it is especially visible on the velor canvas.

Fabric always buy with a reserve. Take a minimum of 100 mm of excess length and widths!

When all the details were carved, the frame was previously produced, the springs are changed, there is a new batting, only then can you begin fitting the tissue cover.

All seams are molded only manually. Marking needles can be applied for fixing. Where the fabric saves, you do not need to trim it immediately, freeze everything to the end and only then you can cut and sew.

If the sewing machine is involved, adjust it for the appropriate tissue. On a separate piece, check the quality of the seam. Where there will be allowances, make small cuts, especially in those places where the fabric goes at a right angle or on an arcuate line.

When the case is sewn, it can be accepted.

Upholstery of a sofa cloth

The next stage, the final, there will be a bend fabric residue.

It is best to fix the fabric in four places, this will serve as a kind of beacon.
With an interval of 2-3 cm, we begin to score the brackets, while simultaneously watching the uniform stretch along the edges of the frame. There should be no relief or accusation. We do the same with the chair.

Here is this, at first glance, simple way You can make the restoration of the old sofa with your own hands!

Any, even the strongest furniture is gradually wear out and acquires an unsightly look. The sofa, as an actively used furniture element, is no exception. The restoration of the sofa will make it possible to return to him attractiveness and functional indispensability.

Repairs soft furniture The easiest way to produce, inviting masters. This approach is quite justified if your sofa is unique and has an antique value or if its design is very complex. In most cases, the restoration of the sofa is a completely real and economical event. The question of how to restore the sofa is solved simply, if you do not regret the time and acquire a quality material.

Useful information

The sofa consists of several elements having a standard design. The main elements can be attributed to the back, sidewalls, seats. In addition, sofas may contain overhead elements (baffics, pillows, etc.), additional mechanisms (mechanism for folding, hinges, etc.) and decorating accessories. In turn, the main elements include frame, upholstery, filler and rear panel. The seating design includes a shock absorbing element.

Frames of the main elements are made of wooden bars different size. Usually, the bars are connected by adhesive compositions, and the joints of the compound can be strengthened with screws. The foam rubber is used as a filler, as well as batting, sintec or other soft synthetic fillers.

The shock absorbing seating element is most often made in the form of springs, but it can be represented by a thickened sheet of foam rubber. Bridal armrests are formed by an additional layer of soft material. All major elements from top view are covered with tissue or leather. To eliminate sagging or pulling the tissue upholstery on the surface of the main elements, tightening elements are used (decorated, for example, in the form of buttons, rivets, etc.).

Back to the category

Basic Restoration Principles: Step-by-step instructions

Any restoration of the old sofa (regardless of its causes) includes the replacement of the upholstery and filler, since the materials of these elements are subjected to the most rapid wear. Replacing or repairing other elements is made as needed when damaged.

The exception is the repair of a sufficiently new sofa during damage to the frame or the shock absorbing element from the mechanical impact or due to production marriage. In this case, the upholstery and filler are preserved in good condition and their replacement is inexpedient. When repairing the upholstery, it is gently removed and a damaged element is replaced, after which the upholstery returns to its place.

If after detection of damage it has come to restore old sofaYou should determine which element will only be repaired, and which is completely replaced. Accordingly, a list of required materials and their number is drawn up.

During the restoration of the sofa, with their own hands, it should be at the same time to solve the issue of the need to make changes to the design. It will not cause special difficulties to make the following improvements: an increase in the thickness of the sidewall; Changing the form of the armrest; Changing the rigidity of the seating and backs, etc.

Back to the category

Choose upholstery

The upholstery of the sofa is the most noticeable and most wearing element of any sofa. The upholstery material must satisfy a number of requirements, such as:

resistance to abrasion;
mechanical tensile strength;
reduced ability to concentrate dust and dirt;
aesthetic appeal;
harmlessness for man;
dye resistance.

Upholstery from leather has many advantages, but costly and difficult in stacking with their own hands. Such a coverage is used, as a rule, if the skin was on the old sofa. A good tapestry is very beautiful and aristocratic, more technologically, but is not much different for the price of leather. At the same time, it should be borne in mind that the skin and tapestry have a long service life.

The choice of the coloring of the fabric is very important both with aesthetic and from the practical side. When selecting fabrics, it is necessary to take into account the need for its combination on different elements of the sofa design and location on the element itself. The smallest waste is achieved when using monochrome tissues and tissues with a small abstract pattern. The overfers of the material occurs when stripping fabrics with a large ornament in the form of geometric figures, lines and cells of different colors.

Dense Food fabric can hide many flaws when it stretched. When choosing a tissue, it is necessary to check that the pile is firmly fixed on the basis. Cotton fabrics Not practical, impenetrate and do not have abrasion resistance. Velor fabrics look good, but have low wear resistance and actively collect dust.

Back to the category

Selection of filler

The foam rubber and syntheton are widely used as a filler. When choosing a material, it should be paid to its quality. Syntheston should have white color Without significant shades. It should not come from unpleasant odors. The strength of the synthetone is such that it is difficult to break it manually; If it is easy to break, then this is poor-quality material.

In the seat and the back, the foam rubber is usually used with a thickness of at least 50 mm or several layers with a thickness of 20 mm. The structure of high-quality foam rubber contains very small pores. When buying a material, it is necessary to check its elastic properties: after pressing a hand to the foam rubber, it must quickly return to the previous position.

Back to the category

Disassembling the sofa and its elements

The restoration of the sofa begins with its complete disassembly. It is performed in the following order. All overhead and decorating elements are removed. Caused sidewalls. Disassembly mechanisms for laying the sofa and fixing elements. The back and seat are separated.

Full disassembly sidewall includes rejunction of legs and accessories, removal of upholstery and extracting the filler. The armrest is dismantled. The carcass strength is checked.

Disassembly of the back starts with rear panel removal. Then the tightening elements are dismantled and the upholstery is removed. Removed filler. The carcass strength is checked.

Disassembling the sofa seating includes dismantling of tightening elements and removal of upholstery. Depreciation elements are extracted. Remove filler. The carcass strength is checked.

It should be borne in mind that in a number of sofas designs, the backrest and seating is carried out by one solid piece of fabric on both elements.

Often the sofa seat is installed on the pallet. Its separation and disassembly completes the disassembly of the entire sofa.

Back to the category

Cutting a new upholstery

Cutting new fabric is the easiest way to spend on the old upholstery. If she managed to remove carefully, she would serve as a lecturer for a new upholstery. With such a plot, it is advisable to add 1-2 cm in all directions, while ensuring the allowance and facilitating the subsequent tension. If the solution is made on the expansion of the sidewall, then the corresponding change is taken into account when stated. If it is impossible to use an old upholstery, measurements of all elements are performed using a roulette and a meter line. Then there is a pattern on paper and cutting fabric.

Regardless of what quality the furniture is in the room, sooner or later it comes in disrepair. Then you need to carry out, for example, repairing a sofa with your own hands. To perform such a job, you need to stock attribute set for mounting, personal desire and the ability to interact with different materials.

Success in carrying out repair activities directly depends on the state in which the frame base is located. Moreover, the sofa of the old sample, made from the chipboard, correct is much more complicated than it can be done with a more modern analogue on wood.

Having studied in detail constructive features This object of furniture can be taken for work.

Design features of the sofa

It is possible to restore the old sofa by repairing or replacing the main elements in the form of legs, supports, locks and tugs of the upholstery layer. All listed types of work require special attention.

There are many sofa models, but each of the varieties is characterized only inherent in the details:

armrests are made of wood, metal, MDF or chipboard, providing softness or rigidity;
unequidence of the upholstery tissues represented by leather or dermatitin;
internal layer of synthesis, batting or furniture foam rubber;
use of polyurethane foam to improve depreciation qualities;
installation of spring block;
application of burlap to prevent squeaks during operation;
the frame is made from natural wood or chipboard.

Attention! The quality and duration of the period of use of the sofa depends on the use of solid materials for the construction frame design and the correct installation. An essential value is attached to an internal filler, which affects comfort and safety.

Remember! You need to disassemble the sofa with side parts, then the back and seat are removed.

Varieties of mechanisms:

the sofa book is used most often;
eurobook is transformed by moving the seat with folding back;
eurobook "Tik-so" moves, occupying a circular position;
"Accordion" is 3 parts that are repaired in rare cases;
the "Click-klyak" device is represented by such positions: the collected, decomposed half and completely;
design "Dolphin" can be seen in the mechanisms of the corner type.

Back to the category

To understand how to repair the sofa, you should deal with the features of the breakdown. If the transforming design failed, it is necessary to replace it with the model under consideration with similar details.

The best sofa samples will be mechanisms on a spring frame with burlap or batting coated. However, such structures will cost expensive. Often to reduce the price, manufacturers take the coarse and foam rubber. In cheaper versions of sofas, blocks on the springs do not put. To start the sofa from the inside, expanded polyurethane foam and stacked with a thick layer.

Repair of the old sofa should be carried out using only qualitative materialsthat will significantly extend the service life. Thus, the thickness of polyurethane foam should not be less than 40 cm. Used Hollofiber allows you to wash the design, the synthet board is able to emphasize the embossed pattern of the sofa, does not absorb moisture. Periothek is distinguished by a high fortress of foundation and is not afraid high temperatures. For spring varieties, it is best to use a 5-cm charter with a layer of rigid matter.

It is possible to replace the external upholstery. For this, fabrics are taken: leather, velor, flock, tapestry, jacquard, shenill. Skin tightness is performed by specialists due to difficulty in carrying out such work. The remaining types of matter allow you to maintain your own.

Back to the category

What may need to work

After studying the design features of the sofa and choosing a suitable fabric, you can begin work to restore its former appearance. To do this, you need to prepare a number of attributes:

screwdriver;
pliers;
stapler;
carpentry glue;
hammer, scissors;
screwdriver and screws.

Back to the category

Upholstery Fabric Replacement Procedure

Before carrying out the main works, the sofa should be disassembled. So that there are no difficulties with the assembly in the future, it is important to remember the order of the details. To do this, they are numbered or imprinted on the camera. After disassembly, the mechanisms are inspected. Strong wear speaks of the need to replace them.

Initially, the side parts are removed, the seat rises and the bolts are unscrewed. Then the main device is taken responsible for the transformation of the model. Seat, back and frame should be unscrewed. Other sofa elements are also cleaned, only the skeleton remains.
Old upholstery should be very accurate to avoid her damage. This canvas will be used as a pattern to a new coating. To dismantle the pillows, they are disconnected from the folding device. Old screws are unscrewed from each side.
To remove the former upholstery fabric, you can use a flat screwdriver. It is raised by a bracket, the part is gradually swinging and is finally removed by pliers. Following the casing is removed, the quality of the lining material is checked. With good condition, it can remain in the same place, after that the new sheathing is stretched from above.
Next sews a case. For this you need to have skills to work on sewing machine. The finished coating is fixed with brackets. At the time of determining the tissue on the surface, it is important to monitor its evenness, folds and wrinkles on it should not be. Manual replacement of the upholstery involves the facet of the front side, at the point of fixing the fabric folds 2 times. Then you can go to the other side and subsequently to the corners.

In the same way, you can repair the remaining elements of the device. Before starting work under fabric, you can put an additional gasket, which contributes to an increase in the life of the sofa. The mounting points can be treated with special glue, which will give the fabric the necessary hardness, and fasteners will be securely.

Over the past ten years, it has become popular to restore the old upholstered furniture - Soviet book-books, dining room chairs, favorite chairs. The reasons forcing people to give a new life to old things, practically sentimental - a sofa-relic, brought by the great-grandfather in the form of a trophy from the war, or a chair in which her grandmother tied the socks for a family in three generations.

But more often, we are surprised to understand that the Quality Soviet Furniture on the quality and integrity of the frame is much better than a new one in low and medium price ranges. Such furniture is often done from a raw bar, cheap spring blocks, and is dragging from above with a cheap and poor-quality cloth.

There have been a great many restorers masters - there are even such craftsmen who may be so transformed appearance The old sofa is that it will not differ from modern fellow design and filling. But, in fact, with minimal shopping skills, desire and patience, hauling up a soft furniture with your own hands - an easy and even creative occupation.

Methods of restoration and furniture upholstery do it yourself

Restoration of furniture allows you to completely transform old interior items

You can update the appearance of upholstered furniture in two ways: washing and replaced. Both variants of rather labor crews and technically cumbersome, but do! All efforts will pay off when you see a sense of complete satisfaction and feel the fruits of your work.

Best of all this option is suitable for small pieces of furniture: seats of chairs, stools and small seats. In the event that the upholstery fabric on the beloved old sofa you like and well preserved, has a unique woven pattern, and you understand that the modern analogue is not available for the price, then the sofa case can be launched in washing.

For washing large furniture covers, it is better to use the services of a professional laundry

Saving money - you spend only time with small expenditure, including the cost of washing agents and furniture fittings (brackets, lining fabric).
Revival of the authentic view of the object of the situation.

Minus one, but significant - the probability is great that the cover when washing "sit down" or will spread out. Since the upholstery fabric is not designed for washing, it is not processed on shrinkage, such as, for example, relaxed fabrics.

Full replacement of the furniture cover

This path is the longest and complex, but sure. Old and dilapidation is ruthlessly emitted, and the sofa can please you with a new fabric of fresh colors. Complete replacement of the furniture cover is quite possible at home. But be prepared for the appearance of problems hidden under the problem: cracked frame beams, broken springs, lacrimated fiberboard or defective locking mechanism.

If, revealing the case, you detected the inner breakdowns with a chagrin, do not despair - just an operation on the replacement of the cover develops into a more complex, capital phase of the upholstered furniture.

Feathering

This relatively new concept includes not only the replacement of the upholstery, as well as: the full repair of the frame, the replacement of the foam rubber, locks, spring blocks, all that will be required. In fact, the hauling is a major overhaul of upholstered furniture, following which you will get a new interior element made in your taste.

Overhaul allows you to save even the most "killed" furniture

Required tools and materials

In order for working on a drawing of upholstered furniture to flow comfortably, measuredly and without unnecessary nerves, you need to prepare the necessary tools in advance.

Instruments D. for disassembly and assembly work

Large flat dumping and pliers - to draw and pull out old brackets.
Conducting or flat screwdriver under the size of the slot of screw heads, fastening the lock to the frame.
Set of keys for nuts and bolts.

Almost all frame furnaces are attached to bolts, so without a set of keys can not do

Roulette - make the necessary measurements when replacing the parts of the housing.
Stapler - construction or pneumatic. The second is preferable, because, without effort on your side, scores deep into the frame of the frame of the long durable brackets, even after a few layers of the tissue.
Staples - from 6 mm to 10 mm depending on the thickness and density of the selected upholstery tissue.
Garbage bags (more and more replenish).

To sewing new covers you will need:

New upholstery fabric - the choice in stores is breathtaking, choose to taste and cost. In order not to make a mistake with the honey, sketch before buying an approximate detail. Consider the standard roll width - up to 145 cm (together with edging edges of the canvas) and the arrangement of the patterns relative to the pile and gloss of matter.
Lining fabric to drive the rear surfaces of the back and seat. It is not necessary to do this, but the lining layer will save the furniture from entering the dust, and the cost of the lining material is small. Therefore, it is better not to neglect this simple operation.
Acute scissors, best special portno for cutting.

When holding new covers, the portnis scissors will be simply indispensable

Small or thin slices of soap.
Threads are not less than 10, and better - special reinforced tissues.
Meter line.
Paper for grids, if you are going to modify the appearance of the product: change the form of the bells, back and seats.
Sewing machine.

Technology Breaks

Disassembly of old furniture

This is the first and dirtiest stage - you have to unscrew and remove the charts, locks and disassemble the framework. Then remove all old brackets that the upholstery is fastened to the frame.

After removing the upholstery, a pretty unsightly picture can open

Take care of the place of disassembly - you will have to stitch the "dust of the centuries", the sofa or chair. And the staples have a submitting habit of flying through the floor and dug in the soles of sneakers (or legs). If there is no possibility to disassemble the sofa on the street, cover the equipment (televisions, computers, etc.) with a film, and everything you can carry out to another room.

Keep your garbage bags at hand - you will have to throw a lot of trash in which the inner sofa filling has turned (chairs, chairs, etc.). Having finished the disassembly, immediately remove the whole garbage from the house. In the inner dust of upholstered furniture can be triggered by various messy - from allergens to the dust tick.

Repair work and replacement parts

Having removed the old cover, you can detect a series of serious breakdowns under harmless hurry, do not hurry to lower your hands and throw away the sofa, counting in the mind, how much will buy a new purchase.

All repair issues are solved, and the details of the replacements are a list of breakdowns and methods for their correction not so extensive and terrible as you may seem at first glance.

Cracked frame beams

All old sofas and armchairs are based on frames bonded by castle and glue. This is a durable and durable system, much better modern mounting Samores. But when the service life ends, the corners of the frames give slack and crack. Beams need to be changed. Choose a dry tree, without knots, cracks and bark - Lob or middle with a flat straightforward structure. Otherwise, beam, carrying a large load, and does not have strength and integrity, quickly burst. The raw tree in warm and dry apartment conditions will begin to push and breast. Castle washed better repeat - Order Master-joiner or do it yourself. The joints of the frame beam in front of the connection is better to impregnate the plow glue.

BRAINED DETAILS FROM DVP (seat liner-jumper seats and backs)

Everything is easier - you measure the size and drink new details on your own logging or placing in the furniture workshop. It is better to prepare separate details of the jumpers (in the old sofas they are usually three - the middle and two side), which in the case of a break is easier to change. Mounting them to the frame can be carnations or a pneumatic stapler.

The burst springs not only worsen the ammontization properties of furniture, but may be caused by injuries and cuts

Sick place is the middle of the seat where children jump and sit guests. Some craftsmen manage to "twist" the spring blocks, changing the burst springs to new ones. However, there is no guarantee that after some time there will be no more than any old spring and for it. It is not necessary to start all the work again. Therefore, rational replace the spring blocks completely.

Replacing belts on seats Chairs

As a belt can perform any dense ribbon of a suitable width.

Usually the frames of the seats and the backs of old chairs are pulled by intertwined wide belts, on which the fear of the porolon. And the belts are very rarely torn, most often the place of the belt and frame connection is wiped. Any belts that you consider solid are suitable for replacement. The main thing is that they are dense weaving, it is desirable from synthetic materials and a width of at least 5 - 7 cm.

Floor foam

Any variety of foam rubber has such technical characteristicsas the number of compression. This is an indicator, how many times the material will withstand compressive and be able to restore its original shape and elasticity. Almost always, in the old furniture, Foolon has long outdressed itself in this parameter and turned into a dust or a viscous substance resembling sticky plasticine. Throw it without regret and iron a new foam rubber.

It is better not to save on the foam rubber - it is not only a soft layer, but also the protection of the inner design from breakdowns

Replacement of castles

Also, a frequent problem - with the time of the steel lock, the lock mechanism is smaller, the backlash appears or flies springs, snatching the lock to the "sitting" or "lying" position. Inspect the lock carefully, it may be necessary to change the screw or adjust the new snack spring. If not, then the castle will have to change - good, it is not a problem, in stores of furniture accessories you will be offered big choice modern castles.

Master class on sewing new covers

The most creative stage of work. You can leave the form of furniture formerly, in this case, you can use old covers as an outfit. Before working, they should be thoroughly shaken and allowed.

When holding out the new details, closely follow the location of the feeds of the duck and the base, as well as the direction of the pile. This is especially true of the cuttings and seat seats, if the width of the tissue does not allow a single cover (meaning the upholstery of a book of a book).

Possessing creative and sewing skills, you can transform the type of old furniture, make it more modern, convenient and appropriate to your taste. The main part of the modifications is achieved by the linings of the foam rubber - soft rollers are added on the air, the backrest linings. You can take into account the location of the body in the sitting position and add foam pads on the seat (kneeling) and insertion under the lower back.

When using extortes, folds, curly parts, covers will receive a completely new form and become more modern.

To qualitatively and beautifully perform work on modifying the appearance of upholstered furniture, the basic skills of cut and sewing are needed. If you are not sure about your abilities, it is better not to risk doing it yourself, but attract a specialist to work.

Nuances cutting and tailoring

Leave the allowances for seams 1 - 1.5 cm depending on the tissue density.

With starting tissue, be sure to leave 1-1.5 centimeters on the seams

Preferably the edges of the stitched parts are treated with overlock or zigzag.

Upholstery fabric with a large pile in front of the machine line you need to shift manually to avoid displacement of parts.
If the upholstery is selected leatherette, artificial or genuine leather, then when performing facial finishing seams as a presser foot sewing machine Use a special video. As a last resort, you can wipe the surface of the fabric under the paw of a thin layer of machine oil.
In case of stitching in the case of decorative linings, hover the folds manually.

As often as possible in the process of sewing, make fittings - a foam, mitigating a rigid spring frame, a malleable material, the form of which is set by the case.

Fastening new covers on the details of upholstered furniture

Repair works are produced, covers are sewn, it's time to start a responsible stage for the tension of the new upholstery. It is necessary to clearly realize that the end result and the appearance of your chair or sofa depends on the quality of this stage. You will need patience and accuracy in work.

At the stage of the last fitting, it will still be possible to fix errors - to sew or release the corners, alter the wrappers. Do not be scared if the case is very tightly put on the frame - in the process of its attachment you still "shink" it is even more denser. Worse, if the case is put on free, because Attaching it with brackets, it is probably possible to get ugly folds and chances.

Sequence of work on the fastening of new upholstery covers:

First of all, put on the covers on the details and, while they are in a free position, repeat as much as possible. The seams should be located smoothly and parallel to the edges of the parts, the corners of the covers compare with the corners of the frames.
Then begin to mount the cover of the brackets - holding a stapler in right handLeft constantly, smooth movements, pull the fabric from the middle of the part to the edge. Follow the smooth and evenly rounded knob - especially it concerns the edges of the backs and seats of chairs and sofas. Starting "shooting" with brackets is better from the middle, so possible excess fabric will be shifted to the edges, where they can be sewn manually.

Stapler - best tool For fastening furniture covers

With the upholstery of the bells gently cut the holes for the bolts for the bolts and shoot the edges of the cuts of the brackets. If necessary, the hammer is densely drive the wood brackets.
After the upholstery stretch, it is necessary to close the origin of the liners of the lining fabric. It is not worth spending time on careful cutting and cutting with lining scissors. Schedule an approximate length, taking into account the edge of the edge of 3-4 cm for each side, make scissors to the lamp and rub the cloth, the lining synthetics rushes exactly along the thread, which you do not get when cutting with scissors. Shot off the lining with the corners, tightly pulling the fabric.

Bymer - (from the Ukrainian) back of bed, chair, armrest of sofa, armchairs, etc.

The last stage of work is an assembly. When assembling the sofa, the first thing is dripped the castle on the back and the seat, then attach the resulting design to the pallet of the book sofa and attach the former. When assembling the chair, you step by step mounted the seat and the back to one fair, then the second is joined to the design. The legs are mounted last.

Restoration helps to turn old furniture In a new, stylish subject of interior

Video: Hauling of an old chair

Since the process of furniture is quite complicated, we bring to your attention a small video, which will clearly demonstrate all the stages of the game, on the example of the restoration of the old chair.

Hauling upholstered furniture with your own hands - the case is responsible, time consuming, but with excellent practical benefits and moral impact. You get satisfaction from the work done and the updated view of the personally renovated object of the situation. And the main thing is the experience that, as to know, can put the beginning of a new passion, and possibly - and profiting business. Good luck to you!

Repair of the sofa with their own hands in the classic style

At home, furniture wear is inevitable. The solution to the problem can be the restoration of the sofa with their own hands. Most often require the replacement external elements, regardless of the type and quality of the material. The fabric fades in the sun, rubbing, the foam loses elasticity and sends.

Praying I. small repairs angular sofa do it yourself

The advantages of restoration do it yourself:

buying material at times cheaper than new furniture;
preservation of antiques;
choice color Gamma. and design, under personal tastes and common interior rooms;
independent choice of material in quality, environmental friendliness, cost;
the possibility of accounting for weak places of the old sofa, their strengthening.

Broken sofa addition mechanism

In addition to external wear, in time there are internal breakdowns. Somewhere appears the creaking, the unfolding mechanism does not work, the springs break through.

Repair of internal filling of the sofa - replacement of springs

Lubricate the creaking parts of the unfolding mechanism

Wooden base can crack, break. In order for the restoration of the old sofa with their own hands, it is necessary to know its approximate structure and methods of repair.

Cracked bar - part of the base

Base bedroomrequiring replacement

Restoration of the Soviet Sofa - new life For old furniture

Conditionally, the sofa can be divided into four parts. it wooden base From an array and chipboard, steel springs and a folding mechanism, filler (foam or batting) and upholstery (tissue, leather, leatherette), decorative elements (wooden lining, buttons).

The process of shaking soft sofa step by step

There are several ways to restore the sofa with their own hands, depending on the complexity:

minor repair of upholstery and decor;
full replacement of the upholstery (hauling);
replacement of upholstery and filler;
replacement of upholstery, filler, mechanisms repair;
full repair of all the details.

Repair of spring mechanism, replacing filler and soft furnace sofa couch

Should not be taken to work if we are talking About antiques, or an old sofa complex structural elements. Work with capricious materials, such as skin, also better entrust to professionals, or change material on the fabric.

Transfiguration of the leather sofa after restoration by experts

Necessary materials and tools

Tools and materials required for repairing upholstered furniture

Restoration of the old sofa will take time. This is a creative process requiring desire, tools and good material. All necessary for repairing a standard sofa 180 * 90 is indicated in the table. Purchase of filler and fabric for upholstery is best done with a margin.

Materials and components for the repair of the sofa do it yourself

The following tools may be required:

building glue;
stapler for furniture;
durable carsional thread, and needle to her;
caid key, pliers, screwdriver;
electrolzik, as a last resort, the usual saw (if a DSP replacement is required).

Variety of furniture repair tools

Fabric to cut in advance to the case. Sew dense elements are hard, so the manufacture of material can be ordered seam. To not be mistaken with dimensions, use old fabric, like a template. With the crop necessarily leave 5-10 centimeters, for fastening, take into account the height of the seating (the width of the back).

Restoration process: Step-by-step instruction

Check the frame and base of the sofa, we produce a replacement in case of breakdown

Before restaving the sofa with your own hands, you need to check the condition of the main framework. If there are cracked or leaning bars, it is better to replace them. An area of \u200b\u200brepair tree requires rarely, but LDSP breaks often. It is not worth repairing it, here you need to completely replace the broken part.

Tighten the bottom base of the sofa, we take the old upholstery as a template

Repair of the back, seats and armrests are slightly different, but in general, the scheme of the restoration of different parts is approximately one.

We replace the upholstery on the inside of the armrests, replace the filler and sew a new case

First of all, you need to make dismantling work:

remove the side armrests (usually the bolts on them are made from the inside, there may be a hexagon key, or pliers);
remove seats and backs with fasteners to lower frame;
remove the old upholstery, the brackets are also removed;
gently carry out the dismantling of the old filler, check on the suitability of reuse;
remove the springs, check their condition, if necessary, clean, lubricate, replace entirely or partially;
check the state of the chipboard, if necessary, replace sheets.

We carry out the replacement of the outer part of the armrests and connect both parts together

All small parts from the pars are better folded into one container not to lose.

Fix the upholstery at the base, use the hammer and stapler if necessary

At the second stage we replace old elements. For fastening parts it is best to use and glue and stapler. But if necessary, you can do through handy means. For example, instead of a stapler, use small carnations:

on both sides of the spring block to lay a dense fabric, on each side, beatened the edges inward and flash the caproove thread;
put the spring frame on a wooden base, fasten the springs through the fabric stapler. If there is no tool, you can make arcuate brackets made of steel wire, or from thin nails, scoring a "hat" to the side;
put a new one or a suitable old, filler;
pull the whole design by a fastening web, on the upholstery manner, consolidate it;
wear a new case, fasten with glue and stapler.

It came a turn of the backs of our divine - we do the work on the same principle

Finishing Stage - Decoration

Fix the outer part of the sofa, decorate with beautiful legs and decorate buttons - we get a great new sofa

Restoration of sofas with their own hands an interesting occupation, as well as its decoration. Here you can simply lay beautiful pillows, or make a carriage tie.

Kareny screed for the back of a new Diana with their own hands

Usually, the backs decorated in this way, leaving the seats with solid. The elements of the screed are simple, you need to prepare buttons, or metal rivets. Cross diagonal can be emphasized with ribbon. So that the foam rubbed smoothly, it is necessary to cut out small circles from the filler at the replacement stage - places for future buttons. Then, cover the cloth and put the selected items. To tighten the buttons, you can use a stapler, or durable threads, tightening them on the other side.

Repair of upholstered furniture with your own hands

If there are elements from wood in the design, on the front part of the armrests, you can glue a curly wooden array in color. Then all the details of the furniture are collected back. It is important to check all the attachments so that during operation it has not moved. That's all, the restoration of the old sofa is finished!